1.4878, X8CrNiTi18-10, AISI 321H - heat-resistant steel. Replacement of 1.4541 grade in heat-resistant version, distinguished from the original by slightly increased content of carbon, a higher range of concentration of titanium and silicon. Classified as heat-resistant steel according to EN 10095, it can operate up to 850 in a neutral
1.4878 Steel Chemical composition, Metal Properties 1.4878. Germany DIN 1.4878 Stainless steel and 1.4878 Mechanical Properties, Chemical Element, Cross Reference, Datasheet.
Oct 19, 2018 · EN 1.4878 stainless-steel is an austenitic chrome steel formulated for primary forming into wrought products. Cited properties are acceptable for the answer annealed (AT) condition. 1.4878 is the EN numeric designation for this material. Both AISI 316 stainless steel and EN 1.4878 stainless steel are iron alloys.
DIN EN 1.4057 Stainless Steel X17CrNi16-2 Material QT800 DIN 1.4057 Steel Properties and Specifications. DIN 1.4057 stainless steel properties and specifications are summarized in the following tables including chemical composition, mechanical properties, hardness, heat treatment, etc. Chemical Composition. X17CrNi16-2 material chemical composition is listed in the following table based on cast analysis.
DIN EN 1.4301 Stainless Steel X5CrNi18-10 Material Notes:EN 10088-2:Technical delivery conditions for stainless steel sheet/plate and strip of corrosion resisting steels for general purposes; Particular ranges of sulfur content may provide improvement of particular properties.For machinability a controlled sulfur content of 0,015 % to 0,030 % is recommended and permitted. For weldability, a controlled sulfur content of 0,008 % to 0,015 % is
EN 10088-3 Mechanical Properties of Martensitic Precipitation. EN 10088-3 gives the mechanical properties for stainless steel semi-finished products, bars, rods and sections for general purposes. This article covers martensitic and precipitation hardening stainless steel. The properties given are proof strength, tensile strength, elongation and hardness.. EN 10088-3 was originally published in
Stainless Steel Equivalent Grades, Stainless Steel stainless steel 1.4571 equivalent, stainless steel 1.4408 equivalent, stainless steel 1.4301 equivalent, stainless steel 1.4541 equivalent, stainless steel 1.4310 equivalent, stainless steel 1.4462 equivalent, stainless steel 310 equivalent, stainless steel aisi 316l equivalent, stainless steel aisi 316 equivalent
Stainless Steel Grades Datasheets British Stainless Stainless Steel Grades Datasheets Introduction. Datasheets for Flat Products Based on EN 10088-2. The table below contains all grades listed in EN 10088-2. In addition, there are some grades not in the current edition but which are expected to be in future editions. 1.4878:321:S32100:ACE. OUT. X15CrNiSi20-12:1.4828:OUT
Care was taken to include as much information as possible about stainless steel flat products used throughout Europe, for the informatio n of the user: Chemical and physical properties are in accordance with EN 10088-1:2005 Mechanical properties are in accordanc e with EN 10088-2:2005, except for he at resisting grad es (EN 100 95:1999)
Stainless steel flat products for building the grades in 2 STAINLESS STEEL FLAT PRODUCTS FOR BUILDING THE GRADES IN EN 1 0 0 8 8 - 4 EXPLAINED Table of contents of EN 10088-4 Note:In this publication, the paragraphs marked in dark blueare specifically expanded on.
Therma range 321 310 309 |Outokumpu Stainless Steel Therma 321H/4878 is an austenitic heat resisting stainless steel with comparable wet corrosion resistance to Core 321/4541 that is best employed in temperatures up to 850 °C/1560 °F. EN 1.4878
EN 10297-2:2005 Seamless circular steel tubes for mechanical and general engineering purposes. Stainless steel. Technical delivery conditions:EN 10088-1:2005 Stainless steels. List of stainless EN 1.4878 (X8CrNiTi18-10) Stainless Steel ::MakeItFromEN 1.4878 stainless steel is an austenitic stainless steel formulated for primary forming into wrought products. Cited properties are appropriate for the solution annealed (AT) condition. 1.4878 is the EN numeric designation for this material. X8CrNiTi18-10 is the EN chemical designation.